国产一区二区av在线免费观看-蜜臀国产一区二区三区在线-久久69国产一区二区蜜臀-久久久蜜臀国产一区二区

Hello! Welcome to the website of Dongguan Youchen Electronic Technology Co., Ltd.

Youchen Technology

Chip Capacitor/Electrolytic Capacitor/Ceramic Capacitor Supplier
18929295505
Current Page: Home > News > Corporate news
News

How to determine short circuit and leakage of SMD capacitors?

2020-08-19
In our daily use Chip capacitorThe common problems are false soldering, short circuit, electric leakage, breakdown, etc. How do we judge whether the patch capacitor is short circuited and electric leakage? Let's take a look at the specific judgment methods below .

What are the phenomena of short circuit and leakage of SMD capacitors? Here is an answer for you.

When the chip capacitor is disconnected, the DC will form an open circuit, leading to abnormal operation of the DC circuit. In other words, when the chip capacitor fails, we can determine whether the capacitor is through or leakage by measuring the DC voltage of the Test point in the circuit. After capacitor breakdown, it will only affect the local circuit of the capacitor.

Because in other circuits, capacitors are still isolated from DC. According to this principle, the maintenance scope can be shortened.

Short circuit and leakage of patch capacitors occur in different circuits, such as coupling circuit short circuit. DC current will directly flow to the next stage, so there should be no current noise, and filter capacitor breakdown may cause fuse.

What is the measurement method for short circuit and leakage of SMD capacitors? There are several methods below.

Method 1: Generally, the resistance value of a small capacitor is infinite, and the abnormal resistance value is replaced. If the capacitance decreases and the multimeter cannot measure it, replace it directly.

Method 2: Use a multimeter to ground one pole to the other and measure both ends of the capacitor. The sound at both ends indicates a short circuit.

Method 3: If the capacitance of the patch is short circuited, a multimeter can be used to measure it online to determine. If it is an open circuit and the capacity is too small to measure a multimeter, you can use a pen to connect a 220V live wire and place the pin of the chip capacitor on the pen cap to see if the neon light bulb is emitting light and the emitting capacitance is good. Otherwise, the circuit will be cut off. 220V voltage, but do not experiment on the board.

Method 4: The resistance value is infinite, a zero resistance value is considered bad, and there should be some small changes in other values.


Summary of issues related to short circuit and leakage of SMD capacitors. During use, it is important to pay attention to the following reasons:


The decrease in surface insulation caused by surface dirt leads to leakage, and this leakage current is not very large, usually at the microampere level. Internal cracks, welding cracks, and MLCC cause severe self suppression cracks, and the leakage current caused by these cracks will continue to increase. In severe cases, it can cause local explosions and fires.

Previous Page:What precautions can be taken to avoid damage to chip capacitors

Next Page:Basic knowledge and main applications of chip capacitors
Youchen Technology
Dongguan Youchen Electronic Technology Co., Ltd
Tel: 0769-85328400 8533526885336465
Fax: 0769-85308615
Email: [email protected]
Website: www.drstephenho.com
Address: Floor 3, No. 7 Xinfeng Road, Shangsha Fourth Industrial Zone, Chang'an Town, Dongguan City, Guangdong Province
Yue ICP Bei No. 13008404
All rights reserved:Dongguan Youchen Electronic Technology Co., Ltd
In-line aluminum electrolytic capacitor manufacturer, SMT aluminum electrolytic capacitor manufacturer, direct sales, brand selection, model selection, price
Follow us:

Do you need our help? Welcome to leave your email!
Subscription
18929295505  
2324774509
[email protected]